{"id":129764,"date":"2020-07-05T13:46:37","date_gmt":"2020-07-05T17:46:37","guid":{"rendered":"https:\/\/www.gunsamerica.com\/digest\/?p=129764"},"modified":"2020-07-05T13:46:37","modified_gmt":"2023-09-06T20:03:25","slug":"building-my-first-belt-fed-semi-auto-rpd-build-part-3","status":"publish","type":"post","link":"https:\/\/gunsamerica.com\/digest\/building-my-first-belt-fed-semi-auto-rpd-build-part-3\/","title":{"rendered":"Building My First Belt-Fed: Semi-Auto RPD Build Part 3"},"content":{"rendered":"\n

Building My First Belt-Fed: Semi-Auto RPD Build Part 2<\/a> <\/h2>\n\n\n\n

<\/p>\n\n\n\n

In part 2, I installed the barrel, components, and pinned them in place. I\u2019ll begin this part by drilling the gas port. Before I could do that, I had to disassemble the gas block. This ended up being a little more difficult than I expected. At first, I was concerned that the parts were rusted together. However, it was just hardened cosmoline. A little heat and application of a 17mm wrench on the bolt, and I was able to disassemble it. <\/p>\n\n\n\n

\"Building
Drilling the gas port requires some care. Go slow, and be careful not to damage the other side of the bore when you breakthrough into it. <\/figcaption><\/figure>\n\n\n\n

Since my parts kit didn\u2019t have the original barrel, I had to do some research to figure out what size the port was supposed to be. For some reason, this information seemed to be rather hard to find. Eventually, I found out the port size is .174\u201d. I used an 11\/64 drill to drill the gas port, as I figured I\u2019d start a little bit small, and if needed I could open it up. It\u2019s not that much of an ordeal to disassemble the gas block (now that I\u2019ve cleaned out the hardened cosmoline) to have access to the port and open it up later. Drilling a gas port into a barrel is a little bit tricky. If you just go to town on it, you run the risk of damaging the opposite side bore when you breakthrough, breaking off the drill bit in your barrel, or both. I tend to lightly \u201cpeck drill\u201d when I\u2019m doing something like this. As I get close to breaking through, I take lighter and lighter pecks to avoid damaging the bore by hitting the other wall. Take your time and use plenty of cutting oil. <\/p>\n\n\n\n

\"Building
I cut the frame rails off with a hacksaw and then used a file to finish fitting it to the receiver. <\/figcaption><\/figure>\n\n\n\n
\"Building
Here is the frame after being shortened and fitted. <\/figcaption><\/figure>\n\n\n\n

The next thing I did was to modify the lower frame to fit the semi-auto receiver. The lower receiver will not fit onto the semi-receiver in its original state. The instructions call for the rails to be removed from 5.750\u201d from the flat where the rear of the receiver butts up to the frame. You can either just cut the whole frame off at that point, or you can just cut the rails and fit the remaining material to the receiver and not have a gap underneath when it\u2019s all together. Mechanically speaking it really doesn\u2019t matter, but I left the tab for aesthetics. I used a hacksaw to remove a chunk of the material. A radius is also required on the inside of the rails of the lower so that they would fit into place on the receiver. This allows the lower to go all the way forward. So then I used a file to add the radius and do the final fitting to the receiver.<\/p>\n\n\n\n

\"Building
Because of the obvious difficulties with where the holes are located and existing features, I used an endmill to machine the holes. <\/figcaption><\/figure>\n\n\n\n

Next, the lower receiver needed the pin holes for the new fire control group drilled in it. The dimensions provided are all referenced from the trigger pin. The holes are .222\u201d up from the trigger pin hole, with a hole 1.155\u201d right, another 2.285\u201d right, and one hole 1.470\u201d to the left of the referenced hole. These locations for these holes are fairly critical, so take your time on this step. The holes are located such that they partially cut into a \u201cwall\u201d. So you can\u2019t just drill them with a regular bit, as the drill bit will be forced out of position by this wall. I used an endmill to machine these holes. I machined the holes on one side and then flipped the frame over to do the holes on the other side.<\/p>\n\n\n\n

\"Building
The pocket is being lengthened on the front end. <\/figcaption><\/figure>\n\n\n\n
\"Building
The web needs to have a slot cut on either side to accommodate the new FCG. <\/figcaption><\/figure>\n\n\n\n

The interior of the frame has to be opened up to accommodate the new semi-auto fire control group. The \u201cpocket\u201d needs to be extended forward, and slots need to be machined into either side of the \u201cweb\u201d. I used an endmill for this task. From the face, the receiver butts up to on the frame, the front of the pocket should be at 4.963\u201d when it is complete. The two slots should be .133\u201d wide on either side of the \u201cweb\u201d.  These features are not critical, in that they only provide clearance for the new fire control group to fit and work. So a few .001s\u201d isn\u2019t really going to matter so long as the parts fit properly. The center portion of the \u201cweb\u201d needs to remain there in order for the spring to push against it as part of the semi-auto functioning. <\/p>\n\n\n\n

\"Building
This is what the pocket should look like after modification. <\/figcaption><\/figure>\n\n\n\n

Next, I machined the trigger. This conversion uses the original trigger. But it requires some modification. It must have a slot machined into it for the new trigger return spring. Trying to hang onto such an odd-shaped item to machine it was a bit tricky. I set the trigger on a parallel and then used a toe clamp to hold it in place. I started with a \u00bc\u201d endmill, centered over the trigger hole. The slot was then cut .130 deep. A secondary notch is also cut .055\u201d deep. It\u2019s kind of hard to describe the slot orientation, but the picture in the instructions shows it fairly well. <\/p>\n\n\n\n

\"Building
The real trick in doing the machine work on the trigger is trying to figure out how to hold onto it. <\/figcaption><\/figure>\n\n\n\n

This semi-auto conversion also uses the original safety,\nagain in a modified form. Because we\u2019re changing the operation of the weapon\nfrom open bolt to closed bolt, it is necessary to add material to it.\nBasically, a blob of weld is added, and then shaped and fitted until the safety\nfits and functions properly. I found it quite difficult to do this, and I ended\nup doing a fair amount of additional work to the safety to get it to work after\nwelding. I have seen it suggested that this is better done by brazing some\nmaterial on the safety rather than actually welding it. Unless you are an\nexcellent TIG welder, I would strongly suggest you go this route and save\nyourself some work.<\/p>\n\n\n\n

\"Building
Here is the safety after modification. Welding this part is quite difficult, and I would consider brazing it instead. <\/figcaption><\/figure>\n\n\n\n

The firing pin is supposed to be removed from the bolt and modified as well. This modification is to reduce the possibility of slam fires caused by the inertia in the firing pin when the bolt closes and stops. Like the safety, a blob of the weld is supposed to be added and fitted to reduce the amount of travel the firing pin has. However, it is quite easy to warp the firing pin or melt it in half. So like the safety, I would also recommend brazing this part as well. It\u2019s supposed to start at 1.194\u201d back from the tip and go back about \u00bc\u201d.<\/p>\n\n\n\n

In the next part, I\u2019ll fit and install the fire control group, do final assembly, and test fire the RPD. Until Next time, Happy Building!<\/p>\n\n\n\n

Buy and Sell on GunsAmerica!<\/a><\/em><\/strong><\/h2>\n","protected":false},"excerpt":{"rendered":"

In part 2, I installed the barrel, components, and pinned them in place. I\u2019ll begin this part by drilling the gas port. <\/p>\n","protected":false},"author":80,"featured_media":129770,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"_specdata_upc":"","_specdata_placement":"","footnotes":""},"categories":[1052],"tags":[132,201,102,2103,614],"featured":[],"hunt365":[],"class_list":{"0":"post-129764","1":"post","2":"type-post","3":"status-publish","4":"format-standard","5":"has-post-thumbnail","7":"category-chris-mace","8":"tag-buzz","9":"tag-diy","10":"tag-feature-articles","11":"tag-gun-build","12":"tag-gunsmithing"},"yoast_head":"\nBuilding My First Belt-Fed: Semi-Auto RPD Build Part 3<\/title>\n<meta name=\"description\" content=\"Building My First Belt-Fed: Semi-Auto RPD Build Part 3 - Chris Mace\" \/>\n<meta name=\"robots\" content=\"index, follow, max-snippet:-1, max-image-preview:large, max-video-preview:-1\" \/>\n<link rel=\"canonical\" href=\"https:\/\/gunsamerica.com\/digest\/building-my-first-belt-fed-semi-auto-rpd-build-part-3\/\" \/>\n<meta property=\"og:locale\" content=\"en_US\" \/>\n<meta property=\"og:type\" content=\"article\" \/>\n<meta property=\"og:title\" content=\"Building My First Belt-Fed: Semi-Auto RPD Build Part 3\" \/>\n<meta property=\"og:description\" content=\"In part 2, I installed the barrel, components, and pinned them in place. I\u2019ll begin this part by drilling the gas port.\" \/>\n<meta property=\"og:url\" content=\"https:\/\/gunsamerica.com\/digest\/building-my-first-belt-fed-semi-auto-rpd-build-part-3\/\" \/>\n<meta property=\"og:site_name\" content=\"Gun Reviews and News | GunsAmerica.com\/Digest\" \/>\n<meta property=\"article:publisher\" content=\"https:\/\/www.facebook.com\/gunsamerica\" \/>\n<meta property=\"article:published_time\" content=\"2020-07-05T17:46:37+00:00\" \/>\n<meta property=\"article:modified_time\" content=\"2023-09-06T20:03:25+00:00\" \/>\n<meta property=\"og:image\" content=\"https:\/\/gunsamerica.com\/digest\/wp-content\/uploads\/2020\/06\/Milling-Pocket-Slots.jpg\" \/>\n\t<meta property=\"og:image:width\" content=\"1200\" \/>\n\t<meta property=\"og:image:height\" content=\"900\" \/>\n\t<meta property=\"og:image:type\" content=\"image\/jpeg\" \/>\n<meta name=\"author\" content=\"Christopher Mace\" \/>\n<meta name=\"twitter:card\" content=\"summary_large_image\" \/>\n<meta name=\"twitter:creator\" content=\"@gunsamerica\" \/>\n<meta name=\"twitter:site\" content=\"@gunsamerica\" \/>\n<meta name=\"twitter:label1\" content=\"Written by\" \/>\n\t<meta name=\"twitter:data1\" content=\"Christopher Mace\" \/>\n\t<meta name=\"twitter:label2\" content=\"Est. reading time\" \/>\n\t<meta name=\"twitter:data2\" content=\"6 minutes\" \/>\n<script type=\"application\/ld+json\" class=\"yoast-schema-graph\">{\"@context\":\"https:\/\/schema.org\",\"@graph\":[{\"@type\":\"Article\",\"@id\":\"https:\/\/gunsamerica.com\/digest\/building-my-first-belt-fed-semi-auto-rpd-build-part-3\/#article\",\"isPartOf\":{\"@id\":\"https:\/\/gunsamerica.com\/digest\/building-my-first-belt-fed-semi-auto-rpd-build-part-3\/\"},\"author\":{\"name\":\"Christopher Mace\",\"@id\":\"https:\/\/gunsamerica.com\/digest\/#\/schema\/person\/d947747eb541fa81bad26ba9ea635d9d\"},\"headline\":\"Building My First Belt-Fed: Semi-Auto RPD Build Part 3\",\"datePublished\":\"2020-07-05T17:46:37+00:00\",\"dateModified\":\"2023-09-06T20:03:25+00:00\",\"mainEntityOfPage\":{\"@id\":\"https:\/\/gunsamerica.com\/digest\/building-my-first-belt-fed-semi-auto-rpd-build-part-3\/\"},\"wordCount\":1269,\"commentCount\":2,\"publisher\":{\"@id\":\"https:\/\/gunsamerica.com\/digest\/#organization\"},\"image\":{\"@id\":\"https:\/\/gunsamerica.com\/digest\/building-my-first-belt-fed-semi-auto-rpd-build-part-3\/#primaryimage\"},\"thumbnailUrl\":\"https:\/\/gunsamerica.com\/digest\/wp-content\/uploads\/2020\/06\/Milling-Pocket-Slots.jpg\",\"keywords\":[\"Buzz\",\"DIY\",\"Feature Articles\",\"Gun Build\",\"Gunsmithing\"],\"articleSection\":[\"Chris Mace\"],\"inLanguage\":\"en-US\",\"potentialAction\":[{\"@type\":\"CommentAction\",\"name\":\"Comment\",\"target\":[\"https:\/\/gunsamerica.com\/digest\/building-my-first-belt-fed-semi-auto-rpd-build-part-3\/#respond\"]}]},{\"@type\":\"WebPage\",\"@id\":\"https:\/\/gunsamerica.com\/digest\/building-my-first-belt-fed-semi-auto-rpd-build-part-3\/\",\"url\":\"https:\/\/gunsamerica.com\/digest\/building-my-first-belt-fed-semi-auto-rpd-build-part-3\/\",\"name\":\"Building My First Belt-Fed: Semi-Auto RPD Build Part 3\",\"isPartOf\":{\"@id\":\"https:\/\/gunsamerica.com\/digest\/#website\"},\"primaryImageOfPage\":{\"@id\":\"https:\/\/gunsamerica.com\/digest\/building-my-first-belt-fed-semi-auto-rpd-build-part-3\/#primaryimage\"},\"image\":{\"@id\":\"https:\/\/gunsamerica.com\/digest\/building-my-first-belt-fed-semi-auto-rpd-build-part-3\/#primaryimage\"},\"thumbnailUrl\":\"https:\/\/gunsamerica.com\/digest\/wp-content\/uploads\/2020\/06\/Milling-Pocket-Slots.jpg\",\"datePublished\":\"2020-07-05T17:46:37+00:00\",\"dateModified\":\"2023-09-06T20:03:25+00:00\",\"description\":\"Building My First Belt-Fed: Semi-Auto RPD Build Part 3 - Chris Mace\",\"breadcrumb\":{\"@id\":\"https:\/\/gunsamerica.com\/digest\/building-my-first-belt-fed-semi-auto-rpd-build-part-3\/#breadcrumb\"},\"inLanguage\":\"en-US\",\"potentialAction\":[{\"@type\":\"ReadAction\",\"target\":[\"https:\/\/gunsamerica.com\/digest\/building-my-first-belt-fed-semi-auto-rpd-build-part-3\/\"]}]},{\"@type\":\"ImageObject\",\"inLanguage\":\"en-US\",\"@id\":\"https:\/\/gunsamerica.com\/digest\/building-my-first-belt-fed-semi-auto-rpd-build-part-3\/#primaryimage\",\"url\":\"https:\/\/gunsamerica.com\/digest\/wp-content\/uploads\/2020\/06\/Milling-Pocket-Slots.jpg\",\"contentUrl\":\"https:\/\/gunsamerica.com\/digest\/wp-content\/uploads\/2020\/06\/Milling-Pocket-Slots.jpg\",\"width\":1200,\"height\":900,\"caption\":\"Building My First Belt-Fed: Semi-Auto RPD Build Part 3\"},{\"@type\":\"BreadcrumbList\",\"@id\":\"https:\/\/gunsamerica.com\/digest\/building-my-first-belt-fed-semi-auto-rpd-build-part-3\/#breadcrumb\",\"itemListElement\":[{\"@type\":\"ListItem\",\"position\":1,\"name\":\"Home\",\"item\":\"https:\/\/gunsamerica.com\/digest\/\"},{\"@type\":\"ListItem\",\"position\":2,\"name\":\"Building My First Belt-Fed: Semi-Auto RPD Build Part 3\"}]},{\"@type\":\"WebSite\",\"@id\":\"https:\/\/gunsamerica.com\/digest\/#website\",\"url\":\"https:\/\/gunsamerica.com\/digest\/\",\"name\":\"Gun Reviews and News | GunsAmerica.com\/Digest\",\"description\":\"Gun Reviews, Industry News, and Product Reviews for Rifles, Pistols, Revolvers, Shotguns, Optics, and Ammunition. Looking to purchase a firearm online? Look no further than GunsAmerica.com, America's premier destination for buying and selling firearms.\",\"publisher\":{\"@id\":\"https:\/\/gunsamerica.com\/digest\/#organization\"},\"potentialAction\":[{\"@type\":\"SearchAction\",\"target\":{\"@type\":\"EntryPoint\",\"urlTemplate\":\"https:\/\/gunsamerica.com\/digest\/?s={search_term_string}\"},\"query-input\":{\"@type\":\"PropertyValueSpecification\",\"valueRequired\":true,\"valueName\":\"search_term_string\"}}],\"inLanguage\":\"en-US\"},{\"@type\":\"Organization\",\"@id\":\"https:\/\/gunsamerica.com\/digest\/#organization\",\"name\":\"GunsAmerica\",\"url\":\"https:\/\/gunsamerica.com\/digest\/\",\"logo\":{\"@type\":\"ImageObject\",\"inLanguage\":\"en-US\",\"@id\":\"https:\/\/gunsamerica.com\/digest\/#\/schema\/logo\/image\/\",\"url\":\"https:\/\/gunsamerica.com\/digest\/wp-content\/uploads\/2026\/01\/image-3.png\",\"contentUrl\":\"https:\/\/gunsamerica.com\/digest\/wp-content\/uploads\/2026\/01\/image-3.png\",\"width\":286,\"height\":156,\"caption\":\"GunsAmerica\"},\"image\":{\"@id\":\"https:\/\/gunsamerica.com\/digest\/#\/schema\/logo\/image\/\"},\"sameAs\":[\"https:\/\/www.facebook.com\/gunsamerica\",\"https:\/\/x.com\/gunsamerica\",\"https:\/\/instagram.com\/gunsamerica_official\/\",\"https:\/\/www.youtube.com\/user\/GunsAmerica\"]},{\"@type\":\"Person\",\"@id\":\"https:\/\/gunsamerica.com\/digest\/#\/schema\/person\/d947747eb541fa81bad26ba9ea635d9d\",\"name\":\"Christopher Mace\",\"image\":{\"@type\":\"ImageObject\",\"inLanguage\":\"en-US\",\"@id\":\"https:\/\/secure.gravatar.com\/avatar\/5cc3df7a2cd8d77197f659eb72f7ff2d8cbdba9337fc4f022c153a5d6874a798?s=96&d=mm&r=g\",\"url\":\"https:\/\/secure.gravatar.com\/avatar\/5cc3df7a2cd8d77197f659eb72f7ff2d8cbdba9337fc4f022c153a5d6874a798?s=96&d=mm&r=g\",\"contentUrl\":\"https:\/\/secure.gravatar.com\/avatar\/5cc3df7a2cd8d77197f659eb72f7ff2d8cbdba9337fc4f022c153a5d6874a798?s=96&d=mm&r=g\",\"caption\":\"Christopher Mace\"},\"description\":\"Christopher Mace enlisted in the US Army as an Infantryman in 2001. He served in the 82nd & 101st Airborne Divisions, with four deployments to Afghanistan & Iraq. Chris started hobby gunsmithing in 2005. After completing his service in 2010, he earned AAS degrees in Machining as well as Welding & Fabrication, and a Gunsmithing Technician Certificate from Trinidad State Junior College. Chris has taken several armorers courses on different firearms, and has built several different types of firearms. He has been collecting & shooting military firearms, old and new since he was 18. Chris enjoys repairing, customizing, building & assembling firearms, as well as different disciplines of competition shooting.\",\"url\":\"https:\/\/gunsamerica.com\/digest\/author\/christopher-mace\/\"}]}<\/script>\n<!-- \/ Yoast SEO Premium plugin. -->","yoast_head_json":{"title":"Building My First Belt-Fed: Semi-Auto RPD Build Part 3","description":"Building My First Belt-Fed: Semi-Auto RPD Build Part 3 - Chris Mace","robots":{"index":"index","follow":"follow","max-snippet":"max-snippet:-1","max-image-preview":"max-image-preview:large","max-video-preview":"max-video-preview:-1"},"canonical":"https:\/\/gunsamerica.com\/digest\/building-my-first-belt-fed-semi-auto-rpd-build-part-3\/","og_locale":"en_US","og_type":"article","og_title":"Building My First Belt-Fed: Semi-Auto RPD Build Part 3","og_description":"In part 2, I installed the barrel, components, and pinned them in place. I\u2019ll begin this part by drilling the gas port.","og_url":"https:\/\/gunsamerica.com\/digest\/building-my-first-belt-fed-semi-auto-rpd-build-part-3\/","og_site_name":"Gun Reviews and News | GunsAmerica.com\/Digest","article_publisher":"https:\/\/www.facebook.com\/gunsamerica","article_published_time":"2020-07-05T17:46:37+00:00","article_modified_time":"2023-09-06T20:03:25+00:00","og_image":[{"width":1200,"height":900,"url":"https:\/\/gunsamerica.com\/digest\/wp-content\/uploads\/2020\/06\/Milling-Pocket-Slots.jpg","type":"image\/jpeg"}],"author":"Christopher Mace","twitter_card":"summary_large_image","twitter_creator":"@gunsamerica","twitter_site":"@gunsamerica","twitter_misc":{"Written by":"Christopher Mace","Est. reading time":"6 minutes"},"schema":{"@context":"https:\/\/schema.org","@graph":[{"@type":"Article","@id":"https:\/\/gunsamerica.com\/digest\/building-my-first-belt-fed-semi-auto-rpd-build-part-3\/#article","isPartOf":{"@id":"https:\/\/gunsamerica.com\/digest\/building-my-first-belt-fed-semi-auto-rpd-build-part-3\/"},"author":{"name":"Christopher Mace","@id":"https:\/\/gunsamerica.com\/digest\/#\/schema\/person\/d947747eb541fa81bad26ba9ea635d9d"},"headline":"Building My First Belt-Fed: Semi-Auto RPD Build Part 3","datePublished":"2020-07-05T17:46:37+00:00","dateModified":"2023-09-06T20:03:25+00:00","mainEntityOfPage":{"@id":"https:\/\/gunsamerica.com\/digest\/building-my-first-belt-fed-semi-auto-rpd-build-part-3\/"},"wordCount":1269,"commentCount":2,"publisher":{"@id":"https:\/\/gunsamerica.com\/digest\/#organization"},"image":{"@id":"https:\/\/gunsamerica.com\/digest\/building-my-first-belt-fed-semi-auto-rpd-build-part-3\/#primaryimage"},"thumbnailUrl":"https:\/\/gunsamerica.com\/digest\/wp-content\/uploads\/2020\/06\/Milling-Pocket-Slots.jpg","keywords":["Buzz","DIY","Feature Articles","Gun Build","Gunsmithing"],"articleSection":["Chris Mace"],"inLanguage":"en-US","potentialAction":[{"@type":"CommentAction","name":"Comment","target":["https:\/\/gunsamerica.com\/digest\/building-my-first-belt-fed-semi-auto-rpd-build-part-3\/#respond"]}]},{"@type":"WebPage","@id":"https:\/\/gunsamerica.com\/digest\/building-my-first-belt-fed-semi-auto-rpd-build-part-3\/","url":"https:\/\/gunsamerica.com\/digest\/building-my-first-belt-fed-semi-auto-rpd-build-part-3\/","name":"Building My First Belt-Fed: Semi-Auto RPD Build Part 3","isPartOf":{"@id":"https:\/\/gunsamerica.com\/digest\/#website"},"primaryImageOfPage":{"@id":"https:\/\/gunsamerica.com\/digest\/building-my-first-belt-fed-semi-auto-rpd-build-part-3\/#primaryimage"},"image":{"@id":"https:\/\/gunsamerica.com\/digest\/building-my-first-belt-fed-semi-auto-rpd-build-part-3\/#primaryimage"},"thumbnailUrl":"https:\/\/gunsamerica.com\/digest\/wp-content\/uploads\/2020\/06\/Milling-Pocket-Slots.jpg","datePublished":"2020-07-05T17:46:37+00:00","dateModified":"2023-09-06T20:03:25+00:00","description":"Building My First Belt-Fed: Semi-Auto RPD Build Part 3 - Chris Mace","breadcrumb":{"@id":"https:\/\/gunsamerica.com\/digest\/building-my-first-belt-fed-semi-auto-rpd-build-part-3\/#breadcrumb"},"inLanguage":"en-US","potentialAction":[{"@type":"ReadAction","target":["https:\/\/gunsamerica.com\/digest\/building-my-first-belt-fed-semi-auto-rpd-build-part-3\/"]}]},{"@type":"ImageObject","inLanguage":"en-US","@id":"https:\/\/gunsamerica.com\/digest\/building-my-first-belt-fed-semi-auto-rpd-build-part-3\/#primaryimage","url":"https:\/\/gunsamerica.com\/digest\/wp-content\/uploads\/2020\/06\/Milling-Pocket-Slots.jpg","contentUrl":"https:\/\/gunsamerica.com\/digest\/wp-content\/uploads\/2020\/06\/Milling-Pocket-Slots.jpg","width":1200,"height":900,"caption":"Building My First Belt-Fed: Semi-Auto RPD Build Part 3"},{"@type":"BreadcrumbList","@id":"https:\/\/gunsamerica.com\/digest\/building-my-first-belt-fed-semi-auto-rpd-build-part-3\/#breadcrumb","itemListElement":[{"@type":"ListItem","position":1,"name":"Home","item":"https:\/\/gunsamerica.com\/digest\/"},{"@type":"ListItem","position":2,"name":"Building My First Belt-Fed: Semi-Auto RPD Build Part 3"}]},{"@type":"WebSite","@id":"https:\/\/gunsamerica.com\/digest\/#website","url":"https:\/\/gunsamerica.com\/digest\/","name":"Gun Reviews and News | GunsAmerica.com\/Digest","description":"Gun Reviews, Industry News, and Product Reviews for Rifles, Pistols, Revolvers, Shotguns, Optics, and Ammunition. Looking to purchase a firearm online? Look no further than GunsAmerica.com, America's premier destination for buying and selling firearms.","publisher":{"@id":"https:\/\/gunsamerica.com\/digest\/#organization"},"potentialAction":[{"@type":"SearchAction","target":{"@type":"EntryPoint","urlTemplate":"https:\/\/gunsamerica.com\/digest\/?s={search_term_string}"},"query-input":{"@type":"PropertyValueSpecification","valueRequired":true,"valueName":"search_term_string"}}],"inLanguage":"en-US"},{"@type":"Organization","@id":"https:\/\/gunsamerica.com\/digest\/#organization","name":"GunsAmerica","url":"https:\/\/gunsamerica.com\/digest\/","logo":{"@type":"ImageObject","inLanguage":"en-US","@id":"https:\/\/gunsamerica.com\/digest\/#\/schema\/logo\/image\/","url":"https:\/\/gunsamerica.com\/digest\/wp-content\/uploads\/2026\/01\/image-3.png","contentUrl":"https:\/\/gunsamerica.com\/digest\/wp-content\/uploads\/2026\/01\/image-3.png","width":286,"height":156,"caption":"GunsAmerica"},"image":{"@id":"https:\/\/gunsamerica.com\/digest\/#\/schema\/logo\/image\/"},"sameAs":["https:\/\/www.facebook.com\/gunsamerica","https:\/\/x.com\/gunsamerica","https:\/\/instagram.com\/gunsamerica_official\/","https:\/\/www.youtube.com\/user\/GunsAmerica"]},{"@type":"Person","@id":"https:\/\/gunsamerica.com\/digest\/#\/schema\/person\/d947747eb541fa81bad26ba9ea635d9d","name":"Christopher Mace","image":{"@type":"ImageObject","inLanguage":"en-US","@id":"https:\/\/secure.gravatar.com\/avatar\/5cc3df7a2cd8d77197f659eb72f7ff2d8cbdba9337fc4f022c153a5d6874a798?s=96&d=mm&r=g","url":"https:\/\/secure.gravatar.com\/avatar\/5cc3df7a2cd8d77197f659eb72f7ff2d8cbdba9337fc4f022c153a5d6874a798?s=96&d=mm&r=g","contentUrl":"https:\/\/secure.gravatar.com\/avatar\/5cc3df7a2cd8d77197f659eb72f7ff2d8cbdba9337fc4f022c153a5d6874a798?s=96&d=mm&r=g","caption":"Christopher Mace"},"description":"Christopher Mace enlisted in the US Army as an Infantryman in 2001. He served in the 82nd & 101st Airborne Divisions, with four deployments to Afghanistan & Iraq. Chris started hobby gunsmithing in 2005. After completing his service in 2010, he earned AAS degrees in Machining as well as Welding & Fabrication, and a Gunsmithing Technician Certificate from Trinidad State Junior College. Chris has taken several armorers courses on different firearms, and has built several different types of firearms. He has been collecting & shooting military firearms, old and new since he was 18. Chris enjoys repairing, customizing, building & assembling firearms, as well as different disciplines of competition shooting.","url":"https:\/\/gunsamerica.com\/digest\/author\/christopher-mace\/"}]}},"featured_image_src":"https:\/\/gunsamerica.com\/digest\/wp-content\/uploads\/2020\/06\/Milling-Pocket-Slots-150x113.jpg","_links":{"self":[{"href":"https:\/\/gunsamerica.com\/digest\/wp-json\/wp\/v2\/posts\/129764","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/gunsamerica.com\/digest\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/gunsamerica.com\/digest\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/gunsamerica.com\/digest\/wp-json\/wp\/v2\/users\/80"}],"replies":[{"embeddable":true,"href":"https:\/\/gunsamerica.com\/digest\/wp-json\/wp\/v2\/comments?post=129764"}],"version-history":[{"count":3,"href":"https:\/\/gunsamerica.com\/digest\/wp-json\/wp\/v2\/posts\/129764\/revisions"}],"predecessor-version":[{"id":186758,"href":"https:\/\/gunsamerica.com\/digest\/wp-json\/wp\/v2\/posts\/129764\/revisions\/186758"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/gunsamerica.com\/digest\/wp-json\/wp\/v2\/media\/129770"}],"wp:attachment":[{"href":"https:\/\/gunsamerica.com\/digest\/wp-json\/wp\/v2\/media?parent=129764"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/gunsamerica.com\/digest\/wp-json\/wp\/v2\/categories?post=129764"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/gunsamerica.com\/digest\/wp-json\/wp\/v2\/tags?post=129764"},{"taxonomy":"featured","embeddable":true,"href":"https:\/\/gunsamerica.com\/digest\/wp-json\/wp\/v2\/featured?post=129764"},{"taxonomy":"hunt365","embeddable":true,"href":"https:\/\/gunsamerica.com\/digest\/wp-json\/wp\/v2\/hunt365?post=129764"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}